root@Alice-Net:~# iw dev wlan0
Usage:	iw [options] command
Options:
	--debug		enable netlink debugging
	--version	show version (5.9-8fab0c9e)
Commands:
	dev <devname> station set <MAC address> txpwr <auto|limit> [<tx power dBm>]
		Set Tx power for this station.

	dev <devname> station set <MAC address> airtime_weight <weight>
		Set airtime weight for this station.

	dev <devname> station set <MAC address> vlan <ifindex>
		Set an AP VLAN for this station.

	dev <devname> station get <MAC address>
		Get information for a specific station.

	dev <devname> station del <MAC address> [subtype <subtype>] [reason-code <code>]
		Remove the given station entry (use with caution!)
		Example subtype values: 0xA (disassociation), 0xC (deauthentication)

	dev <devname> station dump [-v]
		List all stations known, e.g. the AP on managed interfaces

	dev <devname> disconnect
		Disconnect from the current network.

	dev <devname> connect [-w] <SSID> [<freq in MHz>] [<bssid>] [key 0:abcde d:1:6162636465] [mfp:req/opt/no]
		Join the network with the given SSID (and frequency, BSSID).
		With -w, wait for the connect to finish or fail.

	dev <devname> auth <SSID> <bssid> <type:open|shared> <freq in MHz> [key 0:abcde d:1:6162636465]
		Authenticate with the given network.
		

	event [-t|-r] [-f]
		Monitor events from the kernel.
		-t - print timestamp
		-T - print absolute, human-readable timestamp
		-r - print relative timestamp
		-f - print full frame for auth/assoc etc.

	phy <phyname> hwsim getps 
		

	phy <phyname> hwsim setps <value>
		

	phy <phyname> hwsim stopqueues 
		

	phy <phyname> hwsim wakequeues 
		

	dev <devname> ibss leave
		Leave the current IBSS cell.

	dev <devname> ibss join <SSID> <freq in MHz> [NOHT|HT20|HT40+|HT40-|5MHz|10MHz|80MHz] [fixed-freq] [<fixed bssid>] [beacon-interval <TU>] [basic-rates <rate in Mbps,rate2,...>] [mcast-rate <rate in Mbps>] [key d:0:abcde]
		Join the IBSS cell with the given SSID, if it doesn't exist create
		it on the given frequency. When fixed frequency is requested, don't
		join/create a cell on a different frequency. When a fixed BSSID is
		requested use that BSSID and do not adopt another cell's BSSID even
		if it has higher TSF and the same SSID. If an IBSS is created, create
		it with the specified basic-rates, multicast-rate and beacon-interval.

	phy <phyname> info
		Show capabilities for the specified wireless device.

	list
		List all wireless devices and their capabilities.

	phy
	features 
		

	phy <phyname> interface add <name> type <type> [mesh_id <meshid>] [4addr on|off] [flags <flag>*] [addr <mac-addr>]
		Add a new virtual interface with the given configuration.
		Valid interface types are: managed, ibss, monitor, mesh, wds.
		
		The flags are only used for monitor interfaces, valid flags are:
		none:     no special flags
		fcsfail:  show frames with FCS errors
		control:  show control frames
		otherbss: show frames from other BSSes
		cook:     use cooked mode
		active:   use active mode (ACK incoming unicast packets)
		mumimo-groupid <GROUP_ID>: use MUMIMO according to a group id
		mumimo-follow-mac <MAC_ADDRESS>: use MUMIMO according to a MAC address
		
		The mesh_id is used only for mesh mode.

	dev <devname> interface add <name> type <type> [mesh_id <meshid>] [4addr on|off] [flags <flag>*] [addr <mac-addr>]
	dev <devname> del
		Remove this virtual interface

	dev <devname> info
		Show information for this interface.

	dev
		List all network interfaces for wireless hardware.

	help [command]
		Print usage for all or a specific command, e.g.
		"help wowlan" or "help wowlan enable".

	dev <devname> link
		Print information about the current link, if any.

	dev <devname> mesh join <mesh ID> [[freq <freq in MHz> <NOHT|HT20|HT40+|HT40-|80MHz>] [basic-rates <rate in Mbps,rate2,...>]], [mcast-rate <rate in Mbps>] [beacon-interval <time in TUs>] [dtim-period <value>] [vendor_sync on|off] [<param>=<value>]*
		Join a mesh with the given mesh ID with frequency, basic-rates,
		mcast-rate and mesh parameters. Basic-rates are applied only if
		frequency is provided.

	dev <devname> mesh leave
		Leave a mesh.

	dev <devname> mpath probe <destination MAC address> frame <frame>
		Inject ethernet frame to given peer overriding the next hop
		lookup from mpath table.
		.Example: iw dev wlan0 mpath probe xx:xx:xx:xx:xx:xx frame 01:xx:xx:00
		

	dev <devname> mpath get <MAC address>
		Get information on mesh path to the given node.

	dev <devname> mpath del <MAC address>
		Remove the mesh path to the given node.

	dev <devname> mpath new <destination MAC address> next_hop <next hop MAC address>
		Create a new mesh path (instead of relying on automatic discovery).

	dev <devname> mpath set <destination MAC address> next_hop <next hop MAC address>
		Set an existing mesh path's next hop.

	dev <devname> mpath dump
		List known mesh paths.

	dev <devname> mpp get <MAC address>
		Get information on mesh proxy path to the given node.

	dev <devname> mpp dump
		List known mesh proxy paths.

	phy <phyname> channels
		Show available channels.

	reg set <ISO/IEC 3166-1 alpha2>
		Notify the kernel about the current regulatory domain.

	reg get
		Print out the kernel's current regulatory domain information.

	phy <phyname> reg get
		Print out the devices' current regulatory domain information.

	reg reload
		Reload the kernel's regulatory database.

	dev <devname> scan [-u] [freq <freq>*] [duration <dur>] [ies <hex as 00:11:..>] [meshid <meshid>] [lowpri,flush,ap-force,duration-mandatory] [randomise[=<addr>/<mask>]] [ssid <ssid>*|passive]
		Scan on the given frequencies and probe for the given SSIDs
		(or wildcard if not given) unless passive scanning is requested.
		If -u is specified print unknown data in the scan results.
		Specified (vendor) IEs must be well-formed.

	dev <devname> scan dump [-u]
		Dump the current scan results. If -u is specified, print unknown
		data in scan results.

	dev <devname> scan trigger [freq <freq>*] [duration <dur>] [ies <hex as 00:11:..>] [meshid <meshid>] [lowpri,flush,ap-force,duration-mandatory,coloc] [randomise[=<addr>/<mask>]] [ssid <ssid>*|passive]
		Trigger a scan on the given frequencies with probing for the given
		SSIDs (or wildcard if not given) unless passive scanning is requested.
		Duration(in TUs), if specified, will be used to set dwell times.
		

	dev <devname> scan abort 
		Abort ongoing scan

	dev <devname> get mesh_param [<param>]
		Retrieve mesh parameter (run command without any to see available ones).

	phy <phyname> get txq 
		Get TXQ parameters.

	dev <devname> get power_save <param>
		Retrieve power save state.

	dev <devname> set bitrates [legacy-<2.4|5> <legacy rate in Mbps>*] [ht-mcs-<2.4|5> <MCS index>*] [vht-mcs-<2.4|5> [he-mcs-<2.4|5|6> <NSS:MCSx,MCSy... | NSS:MCSx-MCSy>*] [sgi-2.4|lgi-2.4] [sgi-5|lgi-5] [he-gi-<2.4|5|6> <0.8|1.6|3.2>] [he-ltf-<2.4|5|6> <1|2|4>]
		Sets up the specified rate masks.
		Not passing any arguments would clear the existing mask (if any).

	dev <devname> set monitor <flag>*
		Set monitor flags. Valid flags are:
		none:     no special flags
		fcsfail:  show frames with FCS errors
		control:  show control frames
		otherbss: show frames from other BSSes
		cook:     use cooked mode
		active:   use active mode (ACK incoming unicast packets)
		mumimo-groupid <GROUP_ID>: use MUMIMO according to a group id
		mumimo-follow-mac <MAC_ADDRESS>: use MUMIMO according to a MAC address

	dev <devname> set meshid <meshid>
	dev <devname> set type <type>
		Set interface type/mode.
		Valid interface types are: managed, ibss, monitor, mesh, wds.

	dev <devname> set 4addr <on|off>
		Set interface 4addr (WDS) mode.

	dev <devname> set noack_map <map>
		Set the NoAck map for the TIDs. (0x0009 = BE, 0x0006 = BK, 0x0030 = VI, 0x00C0 = VO)

	dev <devname> set mcast_rate <rate in Mbps>
		Set the multicast bitrate.

	dev <devname> set mesh_param <param>=<value> [<param>=<value>]*
		Set mesh parameter (run command without any to see available ones).

	phy <phyname> set name <new name>
		Rename this wireless device.

	phy <phyname> set freq <freq> [NOHT|HT20|HT40+|HT40-|5MHz|10MHz|80MHz|160MHz]
	phy <phyname> set freq <control freq> [5|10|20|40|80|80+80|160] [<center1_freq> [<center2_freq>]]
		Set frequency/channel the hardware is using, including HT
		configuration.

	dev <devname> set freq <freq> [NOHT|HT20|HT40+|HT40-|5MHz|10MHz|80MHz|160MHz]
	dev <devname> set freq <control freq> [5|10|20|40|80|80+80|160] [<center1_freq> [<center2_freq>]]
	phy <phyname> set channel <channel> [NOHT|HT20|HT40+|HT40-|5MHz|10MHz|80MHz|160MHz]
	dev <devname> set channel <channel> [NOHT|HT20|HT40+|HT40-|5MHz|10MHz|80MHz|160MHz]
	phy <phyname> set frag <fragmentation threshold|off>
		Set fragmentation threshold.

	phy <phyname> set rts <rts threshold|off>
		Set rts threshold.

	phy <phyname> set retry [short <limit>] [long <limit>]
		Set retry limit.

	phy <phyname> set netns { <pid> | name <nsname> }
		Put this wireless device into a different network namespace:
		    <pid>    - change network namespace by process id
		    <nsname> - change network namespace by name from /var/run/netns
		               or by absolute path (man ip-netns)
		

	phy <phyname> set coverage <coverage class>
		Set coverage class (1 for every 3 usec of air propagation time).
		Valid values: 0 - 255.

	phy <phyname> set distance <auto|distance>
		Enable ACK timeout estimation algorithm (dynack) or set appropriate
		coverage class for given link distance in meters.
		To disable dynack set valid value for coverage class.
		Valid values: 0 - 114750

	phy <phyname> set txpower <auto|fixed|limit> [<tx power in mBm>]
		Specify transmit power level and setting type.

	dev <devname> set txpower <auto|fixed|limit> [<tx power in mBm>]
		Specify transmit power level and setting type.

	phy <phyname> set antenna <bitmap> | all | <tx bitmap> <rx bitmap>
		Set a bitmap of allowed antennas to use for TX and RX.
		The driver may reject antenna configurations it cannot support.

	phy <phyname> set txq limit <packets> | memory_limit <bytes> | quantum <bytes>
		Set TXQ parameters. The limit and memory_limit are global queue limits
		for the whole phy. The quantum is the DRR scheduler quantum setting.
		Valid values: 1 - 2**32

	phy <phyname> set antenna_gain <antenna gain in dBm>
		Specify antenna gain.

	dev <devname> set power_save <on|off>
		Set power save state to on or off.

	dev <devname> survey dump
		List all gathered channel survey data


Commands that use the netdev ('dev') can also be given the
'wdev' instead to identify the device.

You can omit the 'phy' or 'dev' if the identification is unique,
e.g. "iw wlan0 info" or "iw phy0 info". (Don't when scripting.)

Do NOT screenscrape this tool, we don't consider its output stable.