[ 0.310]AXP22 Voff=3.3V [ 0.313]fel flag = 0x00000000 [ 0.323]DRAM: 512 [ 0.342]MMC3 v5.1 HSDDR52/DDR50 8 bit 7456 MB [ 0.392]Entry_name = u-boot [ 0.400]Entry_name = soc-cfg [ 0.404]Entry_name = dtb [ 0.408]Jump to u-boot U-Boot 2014.07-hg78e7bb6939f0 (Aug 08 2023 - 15:56:03) Allwinner Technology , Build: 78e7bb6939f0 normal mode i2c_init: by cpux [ 0.427]pmbus: ready [ 0.443]PMU: AXP221 [ 0.443]PMU: AXP22X found [ 0.444]PMU: dcdc2 1260 [ 0.445]IC Version: 1(0:A 1:B 2:other) [ 0.449]PMU: pll1 1008 Mhz,PLL6=600 Mhz AXI=336 Mhz,AHB=100 Mhz, APB1=50 Mhz dcdc1_vol = 3000, onoff=1 dcdc2_vol = 1260, onoff=1 dcdc3_vol = 1800, onoff=0 dcdc4_vol = 1100, onoff=1 dcdc5_vol = 1350, onoff=1 aldo1_vol = 3000, onoff=0 aldo2_vol = 1800, onoff=1 aldo3_vol = 3000, onoff=1 dldo1_vol = 1800, onoff=1 dldo2_vol = 3300, onoff=0 dc1sw_vol = 3300, onoff=0 dc5ldo_vol = 1100, onoff=0 DRAM: 512 MiB fdt addr: 0x56ddc0f8 gd->fdt_size: 0x11ec0 Relocation Offset is: 15f3b000 gic: normal mode [ 0.565]MMC: 3 [mmc]: mmc driver ver 2016-08-01 13:45:00 [mmc]: get sdc_ex_dly_used 2, use auto tuning sdly [mmc]: card3 io is 1.8V. [mmc]: get sdc3 sdc_tm4_hs200_max_freq 100. [mmc]: get sdc3 sdc_tm4_hs400_max_freq 100. SUNXI SD/MMC: 3 [mmc]: 50 MHz... [mmc]: sample: 51 - 196(ps) [mmc]: ds: 51 - 196(ps) [mmc]: 100 MHz... [mmc]: sample: 26 - 192(ps) [mmc]: ds: 26 - 192(ps) [mmc]: media type 0x8000000 [mmc]: host caps: 0x1ef [mmc]: MMC3: v5.1 HSSDR52/SDR25 50MHz 8 bit 7456 MB [mmc]: already at HSSDR52_SDR25 mode [mmc]: EOL Info(Rev blks): Normal [mmc]: Wear out(type A): 0%-10% life time used [mmc]: Wear out(type B): 0%-10% life time used [ 0.644]sunxi flash init ok Using default environment bootcmd set setargs_mmc vbus pc exist, limit to pc pre sys mode Bus:2 VBat:4144 Ratio:79 Disable PF0-PF5 SW fel: 1 VBUS req: 0 KEYCOUNTER:1 KEYCOUNTER:2 Entering FEL set next system status sunxi_board_close_source [mmc]: MMC Device 2 not found [mmc]: mmc 2 not find, so not exit [mmc]: mmc exit start [mmc]: 50 MHz... [mmc]: sample: 51 - 196(ps) [mmc]: ds: 51 - 196(ps) [mmc]: 100 MHz... [mmc]: sample: 26 - 192(ps) [mmc]: ds: 25 - 200(ps) [mmc]: mmc 3 exit ok reset cpu [ 0.270]HELLO ;) BOOT0 is starting! [ 0.280]AXP22 Voff=3.3V [ 0.283]fel flag = 0x5aa5a55a [ 0.286]eraly jump fel